Observer Nodes: Difference between revisions
No edit summary |
No edit summary |
||
| Line 3: | Line 3: | ||
|D-Cube makes use of several Raspberry Pi 3 nodes, each connected to a custom add-on card, as unobtrusive observer nodes to measure the reliability, latency, and energy-efficiency of IoT protocols running on a given target platform. | |D-Cube makes use of several Raspberry Pi 3 nodes, each connected to a custom add-on card, as unobtrusive observer nodes to measure the reliability, latency, and energy-efficiency of IoT protocols running on a given target platform. | ||
Each observer, which is powered by PoE and connected via Ethernet to a central server, is completely agnostic to the hardware platform chosen as a target, as long as the latter can be connected via USB to the custom add-on card. | Each observer, which is powered by PoE and connected via Ethernet to a central server, is completely agnostic to the hardware platform chosen as a target, as long as the latter can be connected via USB to the custom add-on card. | ||
The hardware design of the add-on card is openly available on [https://www.tugraz.at/en/institutes/iti/D-Cube GitHub]. | |||
|[[File:empty.png|left|175px]] | |[[File:empty.png|left|175px]] | ||
|[[File:observers_architecture.png|1325px|right]] | |[[File:observers_architecture.png|1325px|right]] | ||
| Line 8: | Line 9: | ||
{| | {| | ||
|The custom add-on card connected to the Raspberry Pi 3 embeds a power and latency profiling unit, as well as a GPIO tracing unit. The power profiling unit captures voltage and current using a 125 kHz simultaneous-sampling 12-bit current and voltage analog-to-digital converter. | |The custom add-on card connected to the Raspberry Pi 3 embeds a power and latency profiling unit, as well as a GPIO tracing unit. The power profiling unit captures voltage and current using a 125 kHz simultaneous-sampling 12-bit current and voltage analog-to-digital converter. The use of optocouplers as isolation layer between the GPIO pins of the target node and the ones of the observer module ensures unbiased energy measurements. | ||
The GPIO tracing and latency profiling units allow simultaneous tracing and actuation of up to 8 GPIO pins per target platform. Observer nodes equipped with a GPS unit can generate precise timestamps for externally triggered events. Nodes without direct GPS connectivity can synchronize to the rest of the network using NTP with a typical accuracy well below 10μs. Target nodes can be individually powered on/off in software, hence allowing to control the network density and to emulate node failures (e.g., due to an early battery depletion) by software. | The GPIO tracing and latency profiling units allow simultaneous tracing and actuation of up to 8 GPIO pins per target platform. Observer nodes equipped with a GPS unit can generate precise timestamps for externally triggered events. Nodes without direct GPS connectivity can synchronize to the rest of the network using NTP with a typical accuracy well below 10μs. Target nodes can be individually powered on/off in software, hence allowing to control the network density and to emulate node failures (e.g., due to an early battery depletion) by software. | ||
|[[File:empty.png|left|275px]] | |[[File:empty.png|left|275px]] | ||
| Line 15: | Line 16: | ||
Under construction. | Under construction. | ||
Revision as of 11:03, 10 November 2019
| D-Cube makes use of several Raspberry Pi 3 nodes, each connected to a custom add-on card, as unobtrusive observer nodes to measure the reliability, latency, and energy-efficiency of IoT protocols running on a given target platform.
Each observer, which is powered by PoE and connected via Ethernet to a central server, is completely agnostic to the hardware platform chosen as a target, as long as the latter can be connected via USB to the custom add-on card. The hardware design of the add-on card is openly available on GitHub. |
 |
 |
| The custom add-on card connected to the Raspberry Pi 3 embeds a power and latency profiling unit, as well as a GPIO tracing unit. The power profiling unit captures voltage and current using a 125 kHz simultaneous-sampling 12-bit current and voltage analog-to-digital converter. The use of optocouplers as isolation layer between the GPIO pins of the target node and the ones of the observer module ensures unbiased energy measurements.
The GPIO tracing and latency profiling units allow simultaneous tracing and actuation of up to 8 GPIO pins per target platform. Observer nodes equipped with a GPS unit can generate precise timestamps for externally triggered events. Nodes without direct GPS connectivity can synchronize to the rest of the network using NTP with a typical accuracy well below 10μs. Target nodes can be individually powered on/off in software, hence allowing to control the network density and to emulate node failures (e.g., due to an early battery depletion) by software. |
|
 |
Under construction.